Will this bumper fit my Toyota Land Cruiser 80 Series (1990-1997)?

Yes, and it fits the Lexus LX450 as well. The Classic Off Road Bumper replaces the front bumper on the 1990-1997 Toyota Land Cruiser 80 Series and on the Lexus LX450, in lightweight SPHC grade steel with full internal reinforcement through the body. [card] You don't give anything up Adding the bumper to the front of the vehicle doesn't take away any standard options. It is compatible with vehicle safety systems, and airbag compatible on airbag-equipped vehicles. [/card] [card] Approach angle for a lifted rig The bumper increases approach angle gains for lifted vehicles, so you get maximum use of every inch of your suspension while picking up increased frontal protection. [/card] [card] The hoop earns its place The A-frame triple hoop protects the headlights and grill, and it gives you a visual reference for the outer front corners of the bumper, which is useful in tight spots. [/card] Hoop tube diameter is 2" (51mm).

What winch fits this bumper?

Any winch using the standard 10" x 4 1/2" mounting bolt pattern goes straight into the Land Cruiser 80 Series Classic bumper, and the winch tray mounting bracket is included in the kit, so the mounting side is sorted before the winch arrives. We don't publish a maximum capacity figure, so the rest of the decision is about clearance. [card] Bolt pattern first If the hole spacing on the base of your winch does not match the 10" x 4 1/2" pattern, it will not mount to the supplied winch tray bracket. [/card] [card] Then the winch body Check drum length, the size of the motor housing, and where the control box sits. A winch that shares the bolt pattern can still be too long or too tall to sit cleanly behind the bumper. [/card] [card] Two-part mounting system The winch tray anchors directly to the chassis rather than to the bumper shell. That is the ideal placement for the winch body on the frame for hard rescues and recoveries: it increases strength, reduces additional front-end weight, and greatly decreases stress on the front of the vehicle. [/card] [card] Clutch handle and fairlead The bumper is laid out for clutch handle access with line spool visibility, so confirm your clutch handle stays reachable and your fairlead lines up square with the drum. [/card] Check your winch's mounting feet against the 10" x 4 1/2" pattern before you order.

How much weight does this add over the factory bumper?

119 lbs , and that figure is already net. It is the additional vehicle weight on the Land Cruiser 80 Series Classic bumper after removing the OEM parts and installing this bumper, so it is the change to the vehicle, not the raw weight of the steel on its own. [card] Why the figure isn't higher The body is lightweight SPHC grade steel, and anchoring the winch tray directly to the chassis instead of hanging it off the bumper reduces the additional front-end weight the vehicle has to carry. [/card] [card] What it means for the install We recommend a second person for the lift, purely down to the sheer weight and size of the bumper, especially with the hoop and the center stone guard attached. Support it while the bolts go in and the alignment comes together much faster. [/card] A winch and any extra lights add to the 119 lbs when you work out the final front-end weight.

What size lights can I mount in the hoop?

The hoop on the Land Cruiser 80 Series Classic bumper takes a light up to 9" across . The bumper is built with accommodations for a wide range of lighting options, and the hoop tube the light clamps to is 2" (51mm) in diameter, which is the figure to check a clamp against. [card] Recessed fog light pockets The fog light pockets are recessed into the bumper and come standard with our halogen lights already in them, wiring harness supplied. [/card] [card] LED running and turn signal lights These are included with the bumper and can be wired in conjunction with the factory lights, so the front-end lighting stays coherent after the swap. [/card] [info] Measure before you buy: 9" is the ceiling for the hoop-mounted light, so measure the lamp body and not just the lens. [/info]

Is this something I can install at home?

Yes! Plan the Land Cruiser 80 Series Classic bumper as a two-stage job . The winch tray mounting bracket goes onto the chassis first, then the bumper mounts over it, which keeps each lift manageable. We recommend a second person when the bumper shell goes into place, simply because of the sheer weight and size of it. Once the OEM parts are off and this bumper is on, the vehicle carries 119 lbs of additional weight. [info] The wiring is the other half: halogen fog lights, LED running lights and turn signal lights all need connecting, and the running and turn signals can be wired in conjunction with the factory lights. [/info] Deep Hi-lift Jack points are reinforced into the bumper, so you won't need separate high lift hooks once it is on. If you would rather have it fitted and wired by a certified dealer, use our store locator to find one near you.

Classic Off Road Bumper for Toyota Land Cruiser 80 Series (1990-1997)

Classic Off Road Bumper for Toyota Land Cruiser 80 Series (1990-1997)

SKU: BBCD004-80LC

Crash Safety Tested

Winch Compatible

Integrated Lights

$1,399.00

$1,699.00

$1,399.00

Warranty

3 Years

Freight Shipping

This item ships at a flat rate of $199 (certain exclusions apply)

Toyota Land Cruiser 80 Series Front Bumper FAQ

Product Information

If you’re looking for the ultimate combination of protection and style for your overland, wheeling, or daily driver look no further. The timeless look of our lightweight outback style bumper isn’t just a pretty package to replace the front bumper of your Lexus LX450 or Toyota 80 Series 4-Wheel Drive, it’s packed with an abundance of features delivering the absolute best value on the market. This highly protective steel bumper increases approach angle gains for lifted vehicles as well as providing increased frontal protection for your rig.

Unlike most brush guards and bull bars on the market, we engineered ours to be the safest and smartest bumper you can install on the front of your vehicle. Ironman 4x4 bumpers go through rigorous testing, including Australian Design Regulation (ADR) compliance, crash safety testing and SRS airbag compliance, to ensure maximum protection for you, your passengers and your vehicle. Adding this bumper to the front of the vehicle doesn't take away any standard options. These bumpers are airbag compatible, (on equipped vehicles), so safety still stays a top priority.

The Ironman 4x4 two-part design provides ideal placement for the winch body on the frame for those dramatic escapes and hard rescues or recoveries. We achieve this by anchoring the winch tray directly to the chassis, increasing strength and reducing additional front-end weight. Making you better equipped to tackle the most demanding recoveries. This design greatly decreases stress on the front of the vehicle and prevents twisting or bending the bumper.

It doesn’t stop there...The Ironman 4x4 Classic off-road bumper includes fog lights, LED indicators, reinforced and integrated Hi-Lift Jack points, and a full hoop. The hoop helps protect the headlights and grill plus you can see the outer front corners of the bumper, helpful in tight spots. Our bumpers also feature a full internal reinforcement ensuring maximum strength and rigidity.

Our bumpers are made with the highest quality SPHC grade steel and sealed using the gold standard in powder coating finishes – AKZO NOBEL powder coat. This results in a top-notch smooth satin finish and provides excellent scratch, rust and corrosion resistance while also reducing UV fading caused in prolonged harsh sun.

Features:

Winch compatible two-part mounting system
Accommodations for a wide range of lighting options
Recessed fog light pockets come standard with Ironman 4x4 halogen lights
ADR 69, 73 approved (Full Frontal and Offset Impact Occupant Protection)
Tested to the highest standards of compliance with Australian Design Regulation
Airbag tested and compatible
Two-part design with direct mount of winch cradle to chassis provides ultimate strength for bold recovery situations
Winch accessibility with clutch handle access with line spool visibility
Oil and pickled rolled steel
Ultra-durable AKZO NOBEL Black Powder Coat and pre-treated steel for rust resistance
360° Robotic welding for consistence and precise welds resulting in peak quality and unequaled strength
A-frame triple hoop design for high level protection
UV stabilized polyurethane bumper over-riders reduce wear while providing light shock absorption from soft impacts
Deep Hi-lift Jack points reinforced into bumper eliminating the need for high lift hooks
LED Parking and Turn signal lights included and can be wired in conjunction with factory
Increase approach angle enhancement gives you maximum use of every inch of your suspension
119LBS of additional vehicle weight after removing OEM parts and installing the Ironman 4x4
Integrated welded antenna mounting point for aerial antenna
Spare and replacement parts available
Standard 10" x 4 1/2" Winch mounting bolt pattern
Hoop tube diameter: 2" (51mm)
Can mount up to a 9" light in the hoop
Lightweight SPHC grade steel construction
Compatible with vehicle safety systems
Designed and engineered using high tech 3d scanning
CNC laser cut and 360-degree robotic welds

Includes:

Classic Bumper
Winch Tray mounting bracket
LED running lights and turn signal lights
Halogen Fog Lights w/ wiring harness
Center stone/brush guard

Make	Model	Year	Installation Guide

5 stars: 15 (88%)
4 stars: 1 (6%)
3 stars: 1 (6%)
2 stars: 0 (0%)
1 star: 0 (0%)

I havent even unwrapped it

I havent even unwrapped it yet, not ready to work on it.

This bumper is everything I

This bumper is everything I expected it to be. Classic styling, tough as hell and perfect for my 80! And the free winch from Black Friday was awesome!

I really like Ironman 4x4

I really like Ironman 4x4 products and this front bull bar bring the old school style I was looking for. Highly recommend.

Looks great. Very high quality. Instant upgrade.

Looks great installed on 97' FJ80. Arrived 3 days after ordering on a pallet packed with incredible care, plastic wrap, cardboard, bubble wrap, neoprene and another layer of wrapping that took 45 minutes to unwarap carefully. About 3 hours to install, including fighting rusty 26 years old New England bolts on the old
stock bumper. Instructions could have larger pictures and the included hardware should be better identified since bolts are of different sizes. All holes aligned perfectly. Excellent welding and paint quality. Not easy to drill the pinning holes (to lock-in up/down and fore/aft movement) once the bumper is installed due to lack of space there. Very good value over competition as it includes integrated fog lights and blinkers with all wiring, relay and dashboard switch, all included (wiring diagram could be better, though).

Lexus Lx450

Absolutely stellar quality. The install instructions were a little sparse but it was pretty intuitive. We had a fitment issue with our apex winch (12000 lb) and part of our radiator. Had to move things around a bit, but no fault of the bumper whatsoever. If you do have a larger winch, don't forget to turn the release handle to engaged before installing. It may not have room to turn afterwards. I will just use the remote in reverse to walk it out I also had to remount the winch wiring housing, but it came with all the necessary parts. This pic is before relocating the electrical housing.

Awesome Bumper, Love It on

Awesome Bumper, Love It on my 94 Cruiser!

Great bumper

This is a quality bumper for a great price. Thanks Ironman!

Exactly what I hoped it was

I love the classic look of these style bumpers, and really like the look on my truck. The fit and finish were top notch, all the hardware was perfect as well. If I have to nit-pick, the only thing I could say was the wiring instructions for the integrated blinker were a little vague. But that's it, and again I'm picking nits. It's an awesome bumper and with a little modification my Apex 12000 winch fits, but I can't use the disengagement lever because the winch isn't clockable. Not the bumpers fault. I just pay it out slower is all. The Ironman winch is similar in price to the Apex, so I might swap it out down the road when I put a winch on another vehicle.

TLDR; Get it.

Me encanto

Fue fácil colocarlo, lo personalize a mi manera, siento que la plancha de abajo pudiera ser más larga y más gruesa

good product

heavy duty, it comes with led foglights that ive always wanted on a bumper. love it

Great looking bumper !

Great looking bumper !

Nice looking, high qualit

Nice looking, high quality bumper. Installation went smoothly. Provides good openings for stock headlights and does not block airflow to radiator.

Great bumper

Great price, great bumper. Lined up perfectly. Wiring was a breeze. Definitely recommend.

Just installed, looks gre

Just installed, looks great. . . very solid

Ironman 80 series Land Cruiser Front bumper

I've now owned the Ironman front bumper for just over a year. It's held up great to PNW weather (rain, snow, and salt. ) I've got a winch mounted and the bumper has taken a beating with winch use as well as using the rubber bumpers to push a buddies keep through a deep mud hole. The rubber bumpers took the abuse and showed no wear or tear on the rubber bumpers. Overall I love the the design with the driving light inserts and integrated turn signals as well. The only downside I can think of is it was a pain to mount because it was so heavy. Great bumper with great design and I get a ton of compliments for a bumper that is different from all the ARB bumpers on other Land Cruisers.

love it.

Built 3 80 series Landcruiser using all 3 Ironman Bullbar says it all. It fit well. It looks good. Provides plenty of protection on the vehicle. And a competitive price. Any future build I will definitely using Ironman Bullbar Delux again.

Great bumper. . . .

Perfect fit and easy to install. This bumper looks awsome.

is it made of steel or aluminum

Brennen G.

Steel. This bumper is made from SPHC grade steel with full internal reinforcement, finished in AKZO NOBEL black powder coat over pre-treated steel for rust resistance.

Classic Bumper Replacement Parts

Replacement Parts

$99.00

$5.00

Replacement Bumper LED Indicators Clear Lens- Pair

$59.00

Replacement Bumper Light Pod & Bracket L/H

$59.00

Replacement Bumper Light Pod & Bracket R/H

$59.00

Replacement Bumper Fog Light Wiring Loom

$49.00

Replacement Classic Bumper Fog Light/Signal Pod Bezel Bracket (Right Hand Side)

$59.00

Replacement Classic Bumper Fog Light/Signal Pod Bezel Bracket (Left Hand Side)

$59.00

Active vehicle

My Build

Let's start by adding your vehicle

Select your Vehicle

Shopping Cart

Classic Off Road Bumper for Toyota Land Cruiser 80 Series (1990-1997)

Required Products

Warranty

Freight Shipping

There are required products for this item. .

Toyota Land Cruiser 80 Series Front Bumper FAQ

Product Information

Overview

Specifications

Vehicle Fitment & Installation

User Guide

Videos

Required Products

Classic Bumper Replacement Parts

Bumper LED Fog Light Upgrade - Pair

Replacement Bumper IRONMAN 4X4 Badge

Replacement Bumper LED Indicators Clear Lens- Pair

Replacement Bumper Light Pod & Bracket L/H

Replacement Bumper Light Pod & Bracket R/H

Replacement Bumper Fog Light Wiring Loom

Replacement Classic Bumper Fog Light/Signal Pod Bezel Bracket (Right Hand Side)

Replacement Classic Bumper Fog Light/Signal Pod Bezel Bracket (Left Hand Side)